Armour Detail | PHOBIC - Spray Coating

User-Friendly Ceramic Coating

Introducing PHOBIC Spray Coating - Armour's most user-friendly ceramic coating solution. PHOBIC integrates the exceptional benefits of traditional ceramic coatings into a convenient spray format, making advanced paint protection easier than ever before.

Leveraging the advanced high-solids chemistry of Armour Quartz coatings, PHOBIC employs next-generation silazane resins to form an exceptionally slick and hydrophobic barrier on paintwork, trim, plastics, and glass. Despite its simple application, PHOBIC provides up to 2 years of durability and delivers the full spectrum of ceramic coating benefits, including superior chemical resistance. PHOBIC can be used as a standalone solution or as part of your existing ceramic coating maintenance regimen. 

Shield your vehicle’s finish with PHOBIC Spray Coating—where simplicity meets exceptional performance.

 

What's Included:

• 90ml Armour PHOBIC - Spray Coating
  
• (2) Spray Pump

Specifications:

Solids Content: ~25%

Hardness: 7H (Who Cares)

Chemical Resistance: High 2-12ph

Durability: 1-2 Years Real World

Film Thickness: ~300nm

Flash Time: 30-60 seconds

Coverage: 10-15ml per car, 15-20ml per large vehicle

Water Contact Angle: 110°+, Low Sliding Angle

Working Temperatures: 40F to 100F.

Applicable Surfaces: Paintwork, Plastics, Trim, Glass

Shelf Life: 12 months, use within 3 months of opening for best application experience. Store with cap sealed tightly in cool dry place.

Precautions:

Shake well.

Wear skin protection.

Wear respiratory protection.

Wear eye protection.

Always test in small area before full application.

Shake well.

Avoid applying in direct sunlight.

Wear skin protection.

Wear respiratory protection.

Wear eye protection.

Always test in small area before full application to determine flash time.

Shelf life of 12 months, use within 3 months of opening when stored correctly.

 

Prep:

The Prep is the most important step of the process, our coating is great but it can not do the prep work for you!

1. Decontaminate the vehicle using Armour Detail Supply Decon Soap and Iron Remover, followed by removing further embedded contamination with a clay bar or synthetic clay mitt.

2. Optional: If swirl marks, or scratches are present, polish the paint to reduce any surface defects and create maximum gloss.

3. Use our Armour Detail Supply Panel Prep to remove any oils/residue left from your polishing step. If you did not polish the surface, repeat this step twice to ensure a clean surface.

You are ready to apply Armour SHIELD Spray Coating!

Application:

1. After thorough prep prime an applicator or short nap towel with 5 sprays to start and each subsequent application will only need 2-3 sprays, a little goes a long way. 

2. Apply PHOBIC 1 panel at a time using overlapping circles (like a wax) making sure to have even, level coverage. Allow the product to “set up” for 30-60 seconds depending on temperature/humidity. Look for uniform small sweat beads or slight hazing to appear before removing.

3. In a similar circular motion level the coating using a plush towel for final leveling. Check for any streaks, or high spots which can appear as cloudy or dark spots. Repeat this process per panel. 

4. Use a fresh side of the plush leveling towel every other panel. The application towel/pad can be used over the whole vehicle.

5. Once finished, remove spray pump from bottle and rinse thoroughly with water or alcohol solution. Secure sealing cap on bottle tightly and store in a cool/dry place for extended use.

Armour PHOBIC Spray Coating was designed as a single layer coating, however, it can be layered. If you wish to apply multiple layers allow 30-60 minutes between layers. This will guarantee optimal performance.

After Care:

Allow product to sit 4 hours for initial cure. After 4 hours you can apply our Armour Detail Supply AMPLIFY or Ceramic Spray Sealant to protect the coating during its initial cure. Do not wash or induce to chemicals for 24 hours.

 

FAQS

Can SHIELD Spray Coating be used over an existing ceramic coating?

Absolutely! SHIELD Spray Coating can be used as a standalone solution or applied over existing ceramic coatings as part of your maintenance routine. We recommend applying SHIELD during your annual maintenance. It integrates seamlessly with your current protection to boost durability and maintain a high-quality finish.

How many vehicles can you coat with the 90ml bottle?

4-9 vehicles depending on size.

Can multiple layers be applied?

Yes! If you wish to apply multiple layers, wait 30-60 minutes between layers.

What surfaces can SHIELD Spray Coating be applied to?

SHIELD Spray Coating is versatile and can be applied to a variety of surfaces, including paintwork, trim, plastics, and glass. This makes it suitable for enhancing and protecting the entire exterior of your vehicle.